« previous next »
Pages: 1 ... 16 17 [18]   Go Down

Author Topic: Dale's k 27 By Kozo  (Read 121627 times)

Offline cnr6400

  • Full Member
  • *****
  • Posts: 3900
Re: Dale's k 27 By Kozo
« Reply #255 on: February 05, 2025, 02:03:31 AM »
 :ThumbsUp: :ThumbsUp: :ThumbsUp: :popcorn: :popcorn: :popcorn:
Logged
"I've cut that stock three times, and it's still too short!"

Offline Roger B

  • Global Moderator
  • Full Member
  • *****
  • Posts: 6935
  • Switzerland
Re: Dale's k 27 By Kozo
« Reply #256 on: March 08, 2025, 08:37:10 AM »
Always good to see a family shot  :)  :) Nice work on the oil pump and brakes  :praise2:
Logged
Best regards

Roger

Offline dalem9

  • Full Member
  • ****
  • Posts: 141
Re: Dale's k 27 By Kozo
« Reply #257 on: March 08, 2025, 09:42:44 PM »
Here is my Tank for the tender. What a job, especially when you put a whole roll of rivits in the wrong place. I have the top edge to solder on and it will be done. The old brain is getting weak!
Logged

Offline RReid

  • Full Member
  • ****
  • Posts: 2107
  • Oregon
Re: Dale's k 27 By Kozo
« Reply #258 on: March 09, 2025, 02:34:04 AM »
A big job for sure, but very nicely done! :ThumbsUp: :ThumbsUp:
Logged
Regards,
Ron

Online crueby

  • Full Member
  • *****
  • Posts: 22670
  • Rochester NY
Re: Dale's k 27 By Kozo
« Reply #259 on: March 09, 2025, 02:40:41 AM »
Impressive  result!
Logged

Online Kim

  • Global Moderator
  • Full Member
  • *****
  • Posts: 9428
  • Portland, Oregon, USA
Re: Dale's k 27 By Kozo
« Reply #260 on: March 09, 2025, 04:33:05 AM »
Very nice looking tank!  :ThumbsUp: :popcorn:

Kim
Logged

Offline dalem9

  • Full Member
  • ****
  • Posts: 141
Re: Dale's k 27 By Kozo
« Reply #261 on: December 07, 2025, 12:08:52 PM »
Here are some pictures of what I have got done. Most of thi was done with 1 hand as I just had my right shoulder replaced.When I needed help the helper GOD made me would come out and help.


Logged

Offline PaulR

  • Full Member
  • ****
  • Posts: 1204
  • Staffordshire, UK
Re: Dale's k 27 By Kozo
« Reply #262 on: December 07, 2025, 02:47:36 PM »
Excellent... think I'll get a new shoulder and see if works as well!  ;D
Logged

Offline dalem9

  • Full Member
  • ****
  • Posts: 141
Re: Dale's k 27 By Kozo
« Reply #263 on: March 05, 2026, 05:38:15 PM »
I finely figure out how  to run the water pipe so it does not hang low to the track. I just had more back surgery again yesterday so I will be gone for awhile again.
Logged

Offline dalem9

  • Full Member
  • ****
  • Posts: 141
Re: Dale's k 27 By Kozo
« Reply #264 on: March 05, 2026, 05:40:54 PM »
I have the tender done except for the coupling and the hoses.
Logged

Offline cnr6400

  • Full Member
  • *****
  • Posts: 3900
Re: Dale's k 27 By Kozo
« Reply #265 on: March 05, 2026, 05:47:13 PM »
 :ThumbsUp: :ThumbsUp: :ThumbsUp: :popcorn: :popcorn: :popcorn:
Logged
"I've cut that stock three times, and it's still too short!"

Online Kim

  • Global Moderator
  • Full Member
  • *****
  • Posts: 9428
  • Portland, Oregon, USA
Re: Dale's k 27 By Kozo
« Reply #266 on: March 05, 2026, 06:04:43 PM »
Wow! That's looking really great!  You've made a lot of progress here.   :ThumbsUp: :popcorn:

Kim
Logged

Offline PaulR

  • Full Member
  • ****
  • Posts: 1204
  • Staffordshire, UK
Re: Dale's k 27 By Kozo
« Reply #267 on: March 05, 2026, 08:59:33 PM »
The rivets!  :NotWorthy:
Logged
Pages: 1 ... 16 17 [18]   Go Up
« previous next »
 
SimplePortal 2.3.5 © 2008-2012, SimplePortal