Author Topic: K-27? lets hope so  (Read 13072 times)

Offline bernienufc

  • Full Member
  • ****
  • Posts: 72
  • Northumberland UK
K-27? lets hope so
« on: April 19, 2026, 04:39:28 pm »
The Kozo books have arrived, even in my wildest expectations did i think they would be so good, i can start to understand why people buy the set and also not part with any.

It is my intention to try to build the 3.5 K-27 with little experience but with a lot of enthusiasm and inspiration from several members on here.

I have several sets of UK steam loco drawings but somehow i just got stuck so i a hoping with the book an this forum i can keep the momentum up.
I am putting the design into cad as i go because a: i have a bit of an issue with swapping digits around :-) and cad allows me to hopefully catch the errors and b: i'm not that ofay with the terminology of steam locos and by drawing them i am getting a good understanding of how they work.
Being a full time carer will restrict my time so short cuts will be (for me) inevitable but one thing i really want to try is to make the boiler, but as a recent helpful member noted by starting at the beginning of the book by the time i get to the boiler i should have more confidence and skills to do it.
First up, sell my huge laser cutter to give some space for a mill, wifey does not mind me doing the model but not in the living room for some reason :-D

Study the books to get a understanding of where i am going, then list my materials and hide it from her indoors.
Onwards and upward  a pleasure to be here

malc

A USA K-27 in the UK, now this should be interesting

Offline crueby

  • Full Member
  • *****
  • Posts: 23955
  • Rochester NY
Re: K-27? lets hope so
« Reply #1 on: April 19, 2026, 05:12:27 pm »
Fun!   Looking forward to seeing your K27 take shape. Years ago my first real scratch big build was his New Shay, learned SO much from following that book.

Online Kim

  • Global Moderator
  • Full Member
  • *****
  • Posts: 9816
  • Portland, Oregon, USA
Re: K-27? lets hope so
« Reply #2 on: April 19, 2026, 05:13:54 pm »
How exciting!
Yes, Kozo's books are very good!  Lots of good techniques and wonderful drawings to look at. I've got the set of books too!

I'm looking forward to seeing your progress on this project!
Kim


Offline Pogo_proptie

  • Full Member
  • ****
  • Posts: 58
Re: K-27? lets hope so
« Reply #3 on: April 28, 2026, 10:07:25 pm »
cool looking foward to another long project..

Offline bent

  • Full Member
  • ****
  • Posts: 1179
  • Wet side of Washington State, USA
Re: K-27? lets hope so
« Reply #4 on: April 29, 2026, 02:46:25 am »
For a moment, I was thinking you were building an RC submarine along the lines of the Russian K-19...but a locomotive works too.  :embarassed:

Offline bernienufc

  • Full Member
  • ****
  • Posts: 72
  • Northumberland UK
Re: K-27? lets hope so
« Reply #5 on: April 29, 2026, 08:33:52 am »
..but a locomotive works too.  :embarassed:

Fingers crossed eh :-)
A USA K-27 in the UK, now this should be interesting

Offline bernienufc

  • Full Member
  • ****
  • Posts: 72
  • Northumberland UK
Re: K-27? lets hope so
« Reply #6 on: May 03, 2026, 03:28:51 pm »
Can someone help me with this Rear Head, i cannot seem to fathom why my lines do not tangent up to the D4 (R2) Circle, i have checked until blue in the face to Kozo's drawing but cannot find my error, anyone who has made this piece did you do it without issue?


many thanks Malc
A USA K-27 in the UK, now this should be interesting

Offline crueby

  • Full Member
  • *****
  • Posts: 23955
  • Rochester NY
Re: K-27? lets hope so
« Reply #7 on: May 03, 2026, 04:07:03 pm »
Kozo does all his drawings pen/ink by hand, not with CAD, so perhaps his dimensions did not calculate out as precisely?

Offline bernienufc

  • Full Member
  • ****
  • Posts: 72
  • Northumberland UK
Re: K-27? lets hope so
« Reply #8 on: May 03, 2026, 04:12:04 pm »
Kozo does all his drawings pen/ink by hand, not with CAD, so perhaps his dimensions did not calculate out as precisely?

I can understand that, but so far i have to say they have been bang on which is why i put it down to me, if i had not used cad i know i would have made a good number of mistakes so looking to solve this before i move on.
Thanks for post
A USA K-27 in the UK, now this should be interesting

Offline crueby

  • Full Member
  • *****
  • Posts: 23955
  • Rochester NY
Re: K-27? lets hope so
« Reply #9 on: May 03, 2026, 05:03:48 pm »
If you want another pair of eyes on his drawing to compare to yours, you could message me a picture of his page, and I'll give it a look.

Online Kim

  • Global Moderator
  • Full Member
  • *****
  • Posts: 9816
  • Portland, Oregon, USA
Re: K-27? lets hope so
« Reply #10 on: May 03, 2026, 05:10:18 pm »
When I look at the drawing in the book, he doesn't seem to specify the radius of those back rounded corners - the ones you show as R2.  He defines the radius of the front round part of the opening as 2R (which matches your 4D).  But the back corners of the tranigle-ish cutout aren't defined in Kozo's drawing.

So you might be trying to overconstrain it?  Just a thought.

Kim

Offline crueby

  • Full Member
  • *****
  • Posts: 23955
  • Rochester NY
Re: K-27? lets hope so
« Reply #11 on: May 03, 2026, 05:54:20 pm »
When I look at the drawing in the book, he doesn't seem to specify the radius of those back rounded corners - the ones you show as R2.  He defines the radius of the front round part of the opening as 2R (which matches your 4D).  But the back corners of the tranigle-ish cutout aren't defined in Kozo's drawing.

So you might be trying to overconstrain it?  Just a thought.

Kim
Not having seen the drawing, but that sounds like it is likely it.

Offline bernienufc

  • Full Member
  • ****
  • Posts: 72
  • Northumberland UK
Re: K-27? lets hope so
« Reply #12 on: May 03, 2026, 06:18:12 pm »
If i change the radius of the 2 rear circles surely the straight lines that join them would not be parallel i.e the 4mm offset if that makes sense.
A USA K-27 in the UK, now this should be interesting

Offline crueby

  • Full Member
  • *****
  • Posts: 23955
  • Rochester NY
Re: K-27? lets hope so
« Reply #13 on: May 03, 2026, 06:22:35 pm »
If i change the radius of the 2 rear circles surely the straight lines that join them would not be parallel i.e the 4mm offset if that makes sense.
Not correct - the lines could still be parallel but the 4mm distance could change so the lines go tangent to the left circle. Does the book show the 4mm distance? Hard to diagnose without having the picture from the book...

Is that 4mm circle supposed to be tangent to the 22mm distance you have it at, or centered on it?

Offline bernienufc

  • Full Member
  • ****
  • Posts: 72
  • Northumberland UK
Re: K-27? lets hope so
« Reply #14 on: May 03, 2026, 07:04:44 pm »
If i change the radius of the 2 rear circles surely the straight lines that join them would not be parallel i.e the 4mm offset if that makes sense.
Not correct - the lines could still be parallel but the 4mm distance could change so the lines go tangent to the left circle. Does the book show the 4mm distance? Hard to diagnose without having the picture from the book...

Is that 4mm circle supposed to be tangent to the 22mm distance you have it at, or centered on it?
Image link sent
A USA K-27 in the UK, now this should be interesting

Offline crueby

  • Full Member
  • *****
  • Posts: 23955
  • Rochester NY
Re: K-27? lets hope so
« Reply #15 on: May 03, 2026, 07:34:09 pm »
Got your image - thanks!  Looked through it and compared your drawing to Kozo's. It was hard to figure it out since your drawing had dimensions in different places than his, and after following through and doing the math to compare them, I found it was quicker for me to make a new drawing in Fusion using his dimension order.

And, nope, it does not work for me either! Something has to give, in those dimensions, it just does not add up. So, I don't think its you, I think Kozo made an error in it. The key would be deciding which things are critical to function, and which dimension is not that important. I would say that the 2mm radius/4mm offset are not critical, it looks like that is just an opening in the side of the part, and unless some other part I am not aware of bears on those edges, then just pick one to change and move forward with it.

Online Kim

  • Global Moderator
  • Full Member
  • *****
  • Posts: 9816
  • Portland, Oregon, USA
Re: K-27? lets hope so
« Reply #16 on: May 03, 2026, 08:26:13 pm »
I agree with Chris.  That opening isn't a critical dimension.  Just make it look good.  Keep the 4mm parallel dimension and the 4mm diameter but move the center of it out a bit.  Or, keep the 4mm diameter in place and move the outer lines in slightly to make them tangent to the 4mm circle.  In either case, you'll have to adjust the rear radii to match.  Just make it look pretty! :)

Kim

Offline bernienufc

  • Full Member
  • ****
  • Posts: 72
  • Northumberland UK
Re: K-27? lets hope so
« Reply #17 on: May 03, 2026, 08:59:35 pm »
Got your image - thanks!  Looked through it and compared your drawing to Kozo's. It was hard to figure it out since your drawing had dimensions in different places than his, and after following through and doing the math to compare them, I found it was quicker for me to make a new drawing in Fusion using his dimension order.

And, nope, it does not work for me either! Something has to give, in those dimensions, it just does not add up. So, I don't think its you, I think Kozo made an error in it. The key would be deciding which things are critical to function, and which dimension is not that important. I would say that the 2mm radius/4mm offset are not critical, it looks like that is just an opening in the side of the part, and unless some other part I am not aware of bears on those edges, then just pick one to change and move forward with it.
That makes me feel better :-) cheers
A USA K-27 in the UK, now this should be interesting

Offline bernienufc

  • Full Member
  • ****
  • Posts: 72
  • Northumberland UK
Re: K-27? lets hope so
« Reply #18 on: May 03, 2026, 08:59:54 pm »
I agree with Chris.  That opening isn't a critical dimension.  Just make it look good.  Keep the 4mm parallel dimension and the 4mm diameter but move the center of it out a bit.  Or, keep the 4mm diameter in place and move the outer lines in slightly to make them tangent to the 4mm circle.  In either case, you'll have to adjust the rear radii to match.  Just make it look pretty! :)

Kim
Will do thank you, onwards and upwards :-)
A USA K-27 in the UK, now this should be interesting

Offline bernienufc

  • Full Member
  • ****
  • Posts: 72
  • Northumberland UK
Re: K-27? lets hope so
« Reply #19 on: May 28, 2026, 02:33:18 pm »
Some drawings done in cad now so i have a much better understanding of the loco, i have got the lathe ready and the mill trammed in just waiting now for some materials to arrive.

Ordered 10mm s275 so i will face that down to 9mm.

You know that you see these locos on forums and tv etc etc and you wait until you a) have the funds b) the skills c) the time or d) all of them but i dont think i fully realised just how much prep work goes on before you even make a chip, i can certainly say its opened my eyes and the respect for those who have built and or building live steam or come to it any model engineering just got even more.

Malc

 
A USA K-27 in the UK, now this should be interesting

Offline bernienufc

  • Full Member
  • ****
  • Posts: 72
  • Northumberland UK
Re: K-27? lets hope so
« Reply #20 on: August 05, 2026, 08:53:58 pm »
After making an error of judgement making the previous set of axle boxes i scrapped all 8 which were in brass.
In a way i am not overly disappointing because i decided to try to do a trial in cast iron as many people seem to recommend this for axle boxes.
So i made 2 and instead of splitting in half i made them as 1 piece which meant trying to cut some grooves for the top half for oil ways.
As i have never used a rotary table i got it a bit out of alignment so glad these were a trial to learn on material and rotary table.

Do anyone see any reason why i should not do 8 like this (more accurately of course) for this loco, i  am just not sure as it does not have an oil bath in the bottom and will rely on just what gets fed into the top

Many thanks Malc
A USA K-27 in the UK, now this should be interesting

Offline Fj45

  • Full Member
  • ****
  • Posts: 46
  • 11hrs early
Re: K-27? lets hope so
« Reply #21 on: August 07, 2026, 05:07:17 am »
 Hi Malc,
 
 New to M.E. but not making and repairing things. Call me strange but I find "reading" engineering drawings a relaxing pastime. In this I am not alone on this site (Ay Chris?). As I have never built/run a loco, I should probably advise taking this with a small pinch of salt, but the wool tips come from helping out on full size traction engines.

 In his K27 book Kozo says on pg28 2. last paragraph "the pocket in the bottom half is packed with oiled yarn to lubricate the journal"
 This yarn stuffed oil pocket is very important. A wad of natural untreated Worsted wool (your lady wife will know) is like a sponge and a wick at the same time. With out it oil poured in the top pocket will seep down around the axle and leave the scene all to quickly. With it oil will run into the bottom pocket and be sponged up by the wool. If the wad of wool reaches the pocket bottom it will wick oil up, if it sits slightly proud at the top of the pocket (touching the axle) it will wipe oil on the axle continuously. Don't make the wad too dense, it's the air space between the fibers that makes it work.

 On pg35 fig 2-13 he shows an oil groove on the axle making the one in your block redundant.

 Pg43 fig 2-32 right shows the Crank/Counterwieght is loctited in place during centering. A one piece block would need to go on first, maybe creating a risk of the loctite gluing the axle to the block?
 If you drive your completed engine allot you may, many years and many miles "Down the Track" wear the axle block bores into an oval, requiring replacement. With the cranks/counterwieghts loctited on I suspect you would be glad of two piece blocks.

 Malc, I have clicked the notify button and will follow (piggyback!!) your learning curve, Kozo's book in hand, with great interest.
« Last Edit: August 07, 2026, 05:10:23 am by Fj45 »
Regards ... Brett

Offline bernienufc

  • Full Member
  • ****
  • Posts: 72
  • Northumberland UK
Re: K-27? lets hope so
« Reply #22 on: August 07, 2026, 10:44:54 am »
Hi Brett, thanks for response, i'll put my bits in yours :-)

Hi Malc,
 
 New to M.E. but not making and repairing things. Call me strange but I find "reading" engineering drawings a relaxing pastime. In this I am not alone on this site (Ay Chris?). As I have never built/run a loco, I should probably advise taking this with a small pinch of salt, but the wool tips come from helping out on full size traction engines.
I love drawings too and technical books especially but i really struggle to read some of it and understand some of it but that does not deter me

 In his K27 book Kozo says on pg28 2. last paragraph "the pocket in the bottom half is packed with oiled yarn to lubricate the journal"
 This yarn stuffed oil pocket is very important. A wad of natural untreated Worsted wool (your lady wife will know) is like a sponge and a wick at the same time. With out it oil poured in the top pocket will seep down around the axle and leave the scene all to quickly. With it oil will run into the bottom pocket and be sponged up by the wool. If the wad of wool reaches the pocket bottom it will wick oil up, if it sits slightly proud at the top of the pocket (touching the axle) it will wipe oil on the axle continuously. Don't make the wad too dense, it's the air space between the fibers that makes it work.
This is really valuable info thanks, if  i go this route thats some learning for me

 On pg35 fig 2-13 he shows an oil groove on the axle making the one in your block redundant.

 Pg43 fig 2-32 right shows the Crank/Counterwieght is loctited in place during centering. A one piece block would need to go on first, maybe creating a risk of the loctite gluing the axle to the block?
 If you drive your completed engine allot you may, many years and many miles "Down the Track" wear the axle block bores into an oval, requiring replacement. With the cranks/counterwieghts loctited on I suspect you would be glad of two piece blocks.
I dont see myself running it around tracks too often, i love the build of items more than when its finished but i would love it to work as it should then i'll put it on the dresser for viewing and run it occasionally when the grandchildren visit around our small garden

 Malc, I have clicked the notify button and will follow (piggyback!!) your learning curve, Kozo's book in hand, with great interest.
At my rate this could be a long journey and i hope you can get into it too :-)
« Last Edit: August 23, 2026, 02:50:41 pm by bernienufc »
A USA K-27 in the UK, now this should be interesting

Offline bernienufc

  • Full Member
  • ****
  • Posts: 72
  • Northumberland UK
Re: K-27? lets hope so
« Reply #23 on: August 23, 2026, 02:50:01 pm »
So its finally started.
The first bits i have ever machined up like this, i cant explain how it feels to hold them knowing it was a big achievement for me, but most of all it should now motivate me to tweak the axle boxes just a teeny bit better then onto some frames.
A USA K-27 in the UK, now this should be interesting

Offline crueby

  • Full Member
  • *****
  • Posts: 23955
  • Rochester NY
Re: K-27? lets hope so
« Reply #24 on: August 23, 2026, 06:17:09 pm »
Great start, nice looking set of parts!  :popcorn:

Online Kim

  • Global Moderator
  • Full Member
  • *****
  • Posts: 9816
  • Portland, Oregon, USA
Re: K-27? lets hope so
« Reply #25 on: August 25, 2026, 02:48:37 am »
Great looking parts!  Good start indeed!  :ThumbsUp: :popcorn: :popcorn:

Kim

Offline bernienufc

  • Full Member
  • ****
  • Posts: 72
  • Northumberland UK
Re: K-27? lets hope so
« Reply #26 on: August 25, 2026, 09:40:56 am »
Thank you kim & crueby

I have a question:
In uk locos they have stretchers along the frame length but there seems to be nothing in the k-27 so what keeps the frames apart in its set positions?
« Last Edit: August 25, 2026, 04:27:48 pm by bernienufc »
A USA K-27 in the UK, now this should be interesting

Offline crueby

  • Full Member
  • *****
  • Posts: 23955
  • Rochester NY
Re: K-27? lets hope so
« Reply #27 on: August 25, 2026, 04:41:10 pm »
I do not have the K27 book, I  built the New Shay, which had a full length frame. Kim?

Offline Rledoux313

  • Full Member
  • ****
  • Posts: 94
Re: K-27? lets hope so
« Reply #28 on: August 25, 2026, 04:47:20 pm »
Following, great start!  :popcorn:

Online Kim

  • Global Moderator
  • Full Member
  • *****
  • Posts: 9816
  • Portland, Oregon, USA
Re: K-27? lets hope so
« Reply #29 on: August 26, 2026, 04:54:12 am »
I dont have access to my books at the moment, but will look in a few days.

Kim

Offline Fj45

  • Full Member
  • ****
  • Posts: 46
  • 11hrs early
Re: K-27? lets hope so
« Reply #30 on: August 26, 2026, 06:40:29 am »
Hi Guys,

 Malcom, your question got me curious, so grabbed the book and took a look.
 No stretchers (cross members) between the drive wheels. Seemed odd to my eyes too, but ya have to think Baldwins had it sorted.
 Began thumbing forward and found chapter 9 "The Link Supports and Crosshead Guides" pg141. There's a photo of the finished unit on that page and one of it fitted on pg148. Question answered maybe??

 For those without the book. These supports and guides either side of the engine are mounted to a pair of steel plates. One above and in front of and one behind drive wheel pair No2. They have silver soldered feet which bolt to the tops of the main frames. These should act as cross members. Hope this helps.

 Malcome, latest crop of parts look great, every bit as good as Kozo's in the book. I'd be right chuffed with those.
Regards ... Brett

Offline bernienufc

  • Full Member
  • ****
  • Posts: 72
  • Northumberland UK
Re: K-27? lets hope so
« Reply #31 on: August 26, 2026, 09:46:22 am »
Thank you all

Brett:thats a great find thank you :-)

Malc
A USA K-27 in the UK, now this should be interesting

Offline PJPickard

  • Full Member
  • ****
  • Posts: 292

Offline bernienufc

  • Full Member
  • ****
  • Posts: 72
  • Northumberland UK
Re: K-27? lets hope so
« Reply #33 on: August 26, 2026, 10:19:47 am »
Hi

They answer my question nicely about stretchers, thank you.

I hope you dont mind but i have downloaded them to look at offline, although never at the skill level to incorporate some of this detail it still wonderful to study and who knows if this one works maybe the next one will be better, especially after seeing some of the k-27 & k-36 models on you tube

thank you very much

Hi,

Here is all I have on the prototype frame:

https://www.dropbox.com/scl/fo/4ec6qv21c02gflrfxvfgi/AKvqLxmYtIQO45I7Be-BRPo?rlkey=arr4yg6louez2xlj3c4evs4iq&st=c0ctvori&dl=0
« Last Edit: August 26, 2026, 10:25:06 am by bernienufc »
A USA K-27 in the UK, now this should be interesting

Online Kim

  • Global Moderator
  • Full Member
  • *****
  • Posts: 9816
  • Portland, Oregon, USA
Re: K-27? lets hope so
« Reply #34 on: August 27, 2026, 05:21:27 pm »
Well, now I'm home and have access to my book.  But it looks like you've got the answer to your question.

As Fj45 says, there are several cross members between the two sides of the frame, but none right at the wheels.  The closest cross member seems to be the one that is effectively made by the  Link Supports and Crosshead Guides (Ch 9, pg 141).

Kim

Offline bernienufc

  • Full Member
  • ****
  • Posts: 72
  • Northumberland UK
Re: K-27? lets hope so
« Reply #35 on: September 21, 2026, 07:59:35 pm »
Beginning to appreciate the effort and time it takes to get things right just the setting up and checking and rechecking time and time again to be sure.

So major step today with first ever silver solder job, it was rear frames and extremely pleased how it went as very worried about it but the solder flowed nice and they are now pickling.

Broke a few taps getting to this point but that's my learning curve, all holes threaded in the frames now so time to paint them up for protection. One thing important that i learnt which is worth a mention for new builders and that is that i was cold chemical blackening my parts and they came out nice but a bit of research has pointed out that it would destroy solder joints or badly affect them at least, so its etch primer and stove paint for me on the rear frames :-)

Malc
A USA K-27 in the UK, now this should be interesting

Offline crueby

  • Full Member
  • *****
  • Posts: 23955
  • Rochester NY
Re: K-27? lets hope so
« Reply #36 on: September 21, 2026, 08:27:52 pm »
Glad its progressing well (and learning lots).
For tapping, I broke a lot fewer taps after getting a tapping holder, like this one (there are many types and brands, this is just one example)https://littlemachineshop.com/products/hand-tapper-mini?_pos=1&_sid=36f04fe61&_ss=r
Also learned to back out/clear chips frequently, especially on blind holes, and to use oil when tapping. And that taps do wear out, when they start being harder to cut with, they are about worn out and will break. And also that steel needs a slightly larger hole than brass... Probably other stuff too!   :cheers:

Offline bernienufc

  • Full Member
  • ****
  • Posts: 72
  • Northumberland UK
Re: K-27? lets hope so
« Reply #37 on: September 21, 2026, 08:36:40 pm »
I have used taps when young mechanic so it was the back and forth that made the success in the end for me here, i was trying to be clever and brought some machine taps thinking this would be the way to go, how wrong i was for me it was back to the old taps and back and forth :-D oh and a look at a holder might help thanks

Glad its progressing well (and learning lots).
For tapping, I broke a lot fewer taps after getting a tapping holder, like this one (there are many types and brands, this is just one example)https://littlemachineshop.com/products/hand-tapper-mini?_pos=1&_sid=36f04fe61&_ss=r
Also learned to back out/clear chips frequently, especially on blind holes, and to use oil when tapping. And that taps do wear out, when they start being harder to cut with, they are about worn out and will break. And also that steel needs a slightly larger hole than brass... Probably other stuff too!   :cheers:
A USA K-27 in the UK, now this should be interesting

Online Kim

  • Global Moderator
  • Full Member
  • *****
  • Posts: 9816
  • Portland, Oregon, USA
Re: K-27? lets hope so
« Reply #38 on: September 21, 2026, 10:59:11 pm »
One thing important that i learnt which is worth a mention for new builders and that is that i was cold chemical blackening my parts and they came out nice but a bit of research has pointed out that it would destroy solder joints or badly affect them at least, so its etch primer and stove paint for me on the rear frames :-)

I had not heard this about chemical blackening.  I understood it to be only creating a surface oxide layer and that it wouldn't negatively affect a hard-soldered joint.  I assume that's what you're talking about, right?  Silver solder?  Not soft solder?

Where did you see this? I'd love to learn if I'm wrong here. Thanks! :-\

Kim

Offline internal_fire

  • Full Member
  • ****
  • Posts: 369
  • Punta Gorda, FL
Re: K-27? lets hope so
« Reply #39 on: September 22, 2026, 12:28:07 am »
I am pretty sure that the detrimental chemical interaction is with soft solder, not silver solder.

Gene

Offline bernienufc

  • Full Member
  • ****
  • Posts: 72
  • Northumberland UK
Re: K-27? lets hope so
« Reply #40 on: September 22, 2026, 10:07:54 am »
Gents
My profuse apologies as you are both correct.
I know in my mind that i read somewhere that it affected silver solder as well as soft solder becasue i so remember being very disappointed that i could not blacken all the frames to match, but with that said i cannot find where i read it so found the statement from Gateros to back up your comments.
Again thank you for picking that up and sorry, next time i'll zip it :-D
I think this bit was maybe in my reading
' Most cold blacking kits use an acidic activator (often containing phosphoric acid or bifluorides). If the silver solder joint has any microscopic porosity, the acid can become trapped. If not meticulously neutralised and sealed with a high-quality dewatering oil, this trapped acid can lead to rapid bleeding and galvanic corrosion right at the joint line.'

Correction for my post.

'While the solution will rapidly turn the S275 carbon steel a deep, uniform black, it treats the silver solder alloy completely differently. Because cold blackening kits rely on a copper-selenium redox reaction designed specifically for iron and low-alloy steels, the silver-rich joint will either resist the chemical entirely or turn an uneven, patchy greyish-brown colour' -Gateros Plating

Quote
I am pretty sure that the detrimental chemical interaction is with soft solder, not silver solder.

Gene
Quote
I assume that's what you're talking about, right?  Silver solder?  Not soft solder?
Where did you see this? I'd love to learn if I'm wrong here. Thanks! :-\
Kim 

« Last Edit: September 22, 2026, 10:11:12 am by bernienufc »
A USA K-27 in the UK, now this should be interesting

Offline bernienufc

  • Full Member
  • ****
  • Posts: 72
  • Northumberland UK
Re: K-27? lets hope so
« Reply #41 on: September 22, 2026, 01:35:50 pm »
i'm having a big moment here, seriously contemplating what to do now.
I have made a number of mistakes some due to dyscalculia some for some reason i cant put my finger on.
I have been meticulous with these rear frames checking rechecking and checking again till i'm blue in the face because i know what i am like, i even wrote on them LH RH Inside Outside, i scribed lines ready for the soldering parts and still i got one on the wrong side, ok so i de-soldered it and found i de-soldered the wrong one so now have done both to realise that as i had machined down the correct sizes there is nowhere to lay the solder on to re-apply them, i am really really down about this because if i tried so hard on these parts and got them so wrong it does not look good for the future.
time for some time out i think to revaluate myself and capability
cheers rant over
A USA K-27 in the UK, now this should be interesting

Online Kim

  • Global Moderator
  • Full Member
  • *****
  • Posts: 9816
  • Portland, Oregon, USA
Re: K-27? lets hope so
« Reply #42 on: September 22, 2026, 05:11:30 pm »
Thanks for the clarification on the chemical blackening. Much appreciated!

I'm sorry to hear you're having such a time with those rear frame pieces. It can be quite frustrating and demoralizing to find you've done something wrong when you've been SO careful to do everything 'right'!  I can relate completely.  On the A3 Switcher, there were several major subassemblies I had to completely redo.  For example, the whole U-shaped coal bin on the tender.  There is a LOT of work and a lot of metal involved in that.  I worked hard on it and was very careful, yet when I went to try and place it on the base, it was so cockeyed that it would have warped everything around it to try and get it to fit.  I struggled with it for a while, then after sleeping on it, decided to redo the whole assembly.  I'm glad I did, because the second time it came out MUCH better. I was able to watch for the steps that caused it to get out of square and did a much better job of it.  Sad as it was, once I got past it, I was really glad I did.

Not that I'm telling you you have to start over.  I'm just relating a story (one of MANY) where I was in a similar predicament and felt hopelessly lost and out of my depth.

Back to your situation at hand.  I went combing through Kozo's K-27 book to see if I could figure out what part you were working on.  If I'm understanding it right, you're talking about the part he calls "Frame Back Sections" on page 55 of Vol 1?  Fig 3-14 shows the extra pieces you silver-solder onto the main frame piece.  And I see he has you do it BEFORE you machine it to shape.  But it seems that you could drill and tap a couple of spots to hold a new piece in place for soldering?  And if you can't reuse the little soldered on pieces, it seems that they aren't that big, and it shouldn't break the bank to cut a couple of new small plates to solder in place?  You could cut those a little oversized on the side that will hang out over the top and edge of the frame piece.  That would give you an edge to set solder, possibly? Then mill or file those edges down to match the rest of the frame.

That's just one idea.  I'm sure after sleeping on it, you'll come up with a plan that will work for you.  I do encourage you NOT to give up. You've doe a lot of beautiful work on this.  Don't let a little setback like this stop you from having fun with the rest of this wonderful project!  ;D

(How's that for a bit of cheerleading?  :Lol:)

Really though.  We've all been through this.  It isn't easy, but then, if it was easy, it wouldn't be so rewarding, would it? :)

Best of luck in figuring out how to proceed.  I'm certain you'll get it figured out!
Kim

Offline Sanjay F

  • Full Member
  • *****
  • Posts: 3028
Re: K-27? lets hope so
« Reply #43 on: September 22, 2026, 05:28:40 pm »
i'm having a big moment here, seriously contemplating what to do now.
I have made a number of mistakes some due to dyscalculia some for some reason i cant put my finger on.
I have been meticulous with these rear frames checking rechecking and checking again till i'm blue in the face because i know what i am like, i even wrote on them LH RH Inside Outside, i scribed lines ready for the soldering parts and still i got one on the wrong side, ok so i de-soldered it and found i de-soldered the wrong one so now have done both to realise that as i had machined down the correct sizes there is nowhere to lay the solder on to re-apply them, i am really really down about this because if i tried so hard on these parts and got them so wrong it does not look good for the future.
time for some time out i think to revaluate myself and capability
cheers rant over

I suffer from the same dyscalculia' as you do (I think we all do!), in fact just 2 days ago I made an error on my build which I measured numerous times, drew out and took what I thought was every precautiuon ............ but no, it was out. I know exactly how frustrating it can be to put all that effort in and find it's has gone awry. Hopefully after some time out you'll get back to it with a fresh pair of eyes  :popcorn: :ThumbsUp:
Best regards

Sanjay

Offline bernienufc

  • Full Member
  • ****
  • Posts: 72
  • Northumberland UK
Re: K-27? lets hope so
« Reply #44 on: September 22, 2026, 05:36:10 pm »
Thank you Kim for the encouragement it really makes a difference and thank you Sanjay its amazing that i don't feel so bad knowing that someone else is going through a similar thing, i found that i swap numbers like 20.105 would become 20.501 no matter how many times i checked it so i don't feel so alone so to say :-)

Kim, i did put some bolts though and nice tip i found (yes i'll put this one out there) chalk on the threads to stop the solder sticking to them which worked :-), i only had the one ledge for the solder so when i redid it the solder went right the way through the piece (yes Kim your are correct with the piece i am doing), i was amazed and felt not all was bad, so once again a recovery that i am happy with so time me to take a kicking and knuckle down as you are all right its what we are here for :-D

thanks again
A USA K-27 in the UK, now this should be interesting

Offline bernienufc

  • Full Member
  • ****
  • Posts: 72
  • Northumberland UK
Re: K-27? lets hope so
« Reply #45 on: September 25, 2026, 09:04:56 pm »
I'd like some sort of pointer here if possible please, we are talking about the cranks here.
As my lathe is not up to doing the level of work required without a lot of struggle and a friend has offered to use his biggy lathe for us to do them.
My original plan was to follow the book using the mill for most of the work once i got them faced down to thickness but the friend has said we could do most of the cutting and reaming in one go if i wanted.

Is there a reason for me to follow the book or just getting on the biggy and doing most of it there?

cheers malc
A USA K-27 in the UK, now this should be interesting

Online Kim

  • Global Moderator
  • Full Member
  • *****
  • Posts: 9816
  • Portland, Oregon, USA
Re: K-27? lets hope so
« Reply #46 on: September 28, 2026, 07:33:51 pm »
Sorry for the late reply, I was out all weekend. :)

I'm not certain what part you're referring to, I looked through the book quickly and didn't see anything called a crank, though I'm sure it could refer to several different parts.  Regardless, I'd say make the part the way that makes sense to you.  I don't see any reason you have to use Kozo's methods.  I deviated from his methods many times.  He documents a good way to do it, if you have equipment similar to his.  But since you have access to different tools, a different method may work great for you. So, go for it! :)

How's that for wishy-washy advice?  :Lol:

Kim

Offline internal_fire

  • Full Member
  • ****
  • Posts: 369
  • Punta Gorda, FL
Re: K-27? lets hope so
« Reply #47 on: September 28, 2026, 08:57:03 pm »
Is there a reason for me to follow the book or just getting on the biggy and doing most of it there?

There are only two items that are critical on the cranks. Namely the size and position of the two holes, axle and crankpin. Everything else is essentially cosmetic.

The entire crank is less than 4" in extent, so it should be possible to machine it on the equipment found in most home shops.

If you want to use the "biggy" lathe of course that is completely up to you.  :)

Gene

Offline bernienufc

  • Full Member
  • ****
  • Posts: 72
  • Northumberland UK
Re: K-27? lets hope so
« Reply #48 on: September 28, 2026, 09:21:28 pm »


How's that for wishy-washy advice?  :Lol:

Kim

It certainly works for me :-D thank you
A USA K-27 in the UK, now this should be interesting

Offline bernienufc

  • Full Member
  • ****
  • Posts: 72
  • Northumberland UK
Re: K-27? lets hope so
« Reply #49 on: September 28, 2026, 09:23:52 pm »
Is there a reason for me to follow the book or just getting on the biggy and doing most of it there?

There are only two items that are critical on the cranks. Namely the size and position of the two holes, axle and crankpin. Everything else is essentially cosmetic.

The entire crank is less than 4" in extent, so it should be possible to machine it on the equipment found in most home shops.

If you want to use the "biggy" lathe of course that is completely up to you.  :)

Gene

Thank you gene
Today i had a chat with an engineer who looked it over and said i would be better using the mill and rotary table but did agree that most of it was cosmetic except for the holes as you mention

A USA K-27 in the UK, now this should be interesting

Offline bernienufc

  • Full Member
  • ****
  • Posts: 72
  • Northumberland UK
Re: K-27? lets hope so
« Reply #50 on: October 08, 2026, 06:28:54 pm »
If i ever do another loco i am going to do a 0-4-0 or an 0-2-0 if there is one  :ROFL:
A USA K-27 in the UK, now this should be interesting

Offline crueby

  • Full Member
  • *****
  • Posts: 23955
  • Rochester NY
Re: K-27? lets hope so
« Reply #51 on: October 08, 2026, 07:00:27 pm »
If i ever do another loco i am going to do a 0-4-0 or an 0-2-0 if there is one  :ROFL:
I'd LOVE to see an 0-2-0!   :lolb:   There must be one designed by Wile E Coyote...

Offline bernienufc

  • Full Member
  • ****
  • Posts: 72
  • Northumberland UK
Re: K-27? lets hope so
« Reply #52 on: October 08, 2026, 08:00:43 pm »
If i ever do another loco i am going to do a 0-4-0 or an 0-2-0 if there is one  :ROFL:
I'd LOVE to see an 0-2-0!   :lolb:   There must be one designed by Wile E Coyote...

:-D
A USA K-27 in the UK, now this should be interesting

Offline cnr6400

  • Full Member
  • *****
  • Posts: 4227
Re: K-27? lets hope so
« Reply #53 on: October 08, 2026, 08:29:26 pm »
Just fyi there were / are a couple of real steam locomotives classed as 0-3-0, one used on a monorail system called "Lartigue" in Ireland, and also a similar system in India. Some pics are available in Google if you search for "0-3-0 locomotive".

I see you already found the pic of "Tippy" the 0-2-0... :Lol:
"I've cut that stock three times, and it's still too short!"

Offline bernienufc

  • Full Member
  • ****
  • Posts: 72
  • Northumberland UK
Re: K-27? lets hope so
« Reply #54 on: October 08, 2026, 08:48:51 pm »
I hadn't even realised until after i posted, and after seeing 'tippy' maybe a unicycle   :Lol:
Everyday a school day

Just fyi there were / are a couple of real steam locomotives classed as 0-3-0, one used on a monorail system called "Lartigue" in Ireland, and also a similar system in India. Some pics are available in Google if you search for "0-3-0 locomotive".

I see you already found the pic of "Tippy" the 0-2-0... :Lol:
A USA K-27 in the UK, now this should be interesting

Offline uuu

  • Full Member
  • ****
  • Posts: 361
Re: K-27? lets hope so
« Reply #55 on: October 09, 2026, 08:04:27 am »

Offline bernienufc

  • Full Member
  • ****
  • Posts: 72
  • Northumberland UK
Re: K-27? lets hope so
« Reply #56 on: October 09, 2026, 09:25:22 am »
A USA K-27 in the UK, now this should be interesting

Offline cnr6400

  • Full Member
  • *****
  • Posts: 4227
Re: K-27? lets hope so
« Reply #57 on: October 09, 2026, 07:36:42 pm »
Just a suggestion if you build the light blue 0-3-0 - you may need a slightly taller smokestack / chimney to get a good draft for the fire... :Lol:   :cheers:
"I've cut that stock three times, and it's still too short!"

Offline uuu

  • Full Member
  • ****
  • Posts: 361
Re: K-27? lets hope so
« Reply #58 on: October 10, 2026, 07:21:16 am »
It really is a curious loco - the firehole is in the side of the boiler.  See it in action here:

<a href="https://www.youtube.com/watch?v=ilBsu3vrVQY" target="_blank">http://www.youtube.com/watch?v=ilBsu3vrVQY</a>

Wilf

Offline Sanjay F

  • Full Member
  • *****
  • Posts: 3028
Re: K-27? lets hope so
« Reply #59 on: October 10, 2026, 08:08:35 am »
Is that guy assisting the wheel with a crowbar at 4:09???  :o
Best regards

Sanjay

Offline bernienufc

  • Full Member
  • ****
  • Posts: 72
  • Northumberland UK
Re: K-27? lets hope so
« Reply #60 on: October 10, 2026, 12:57:22 pm »
It really is a curious loco - the firehole is in the side of the boiler.
Wilf

Great video nice to see something different too :-)
A USA K-27 in the UK, now this should be interesting

Offline internal_fire

  • Full Member
  • ****
  • Posts: 369
  • Punta Gorda, FL
Re: K-27? lets hope so
« Reply #61 on: October 10, 2026, 06:32:13 pm »
It really is a curious loco - the firehole is in the side of the boiler.

It has been quite a few years since I visited, but I believe the double Fairlie locomotives on the Ffestiniog Railway in Wales have fireholes in the side of the boiler. Two fireholes, actually, one for each boiler. They are side-by-side so the fireman can load both without moving from his position.

Gene

Offline bernienufc

  • Full Member
  • ****
  • Posts: 72
  • Northumberland UK
Re: K-27? lets hope so
« Reply #62 on: October 10, 2026, 06:53:04 pm »
Its a strange old game,"I never noticed narrow gauge (except in Wales) until I saw Kozo's K-27 book about one, and now I seem to have found a new area of interest."


It really is a curious loco - the firehole is in the side of the boiler.

It has been quite a few years since I visited, but I believe the double Fairlie locomotives on the Ffestiniog Railway in Wales have fireholes in the side of the boiler. Two fireholes, actually, one for each boiler. They are side-by-side so the fireman can load both without moving from his position.

Gene
A USA K-27 in the UK, now this should be interesting

 

SimplePortal 2.3.5 © 2008-2012, SimplePortal