Author Topic: Hello from Perth, Australia  (Read 1209 times)

Offline perthjack

  • Jr. member
  • **
  • Posts: 2
Hello from Perth, Australia
« on: June 28, 2023, 05:03:58 PM »
Hi all I'm Trev from Perth. I have been retired for several years and I think I have completed the wife's list of to do stuff. So it is time to start and make things, or at least find out how and try :) I have had a Hafco A320G Lathe for about 6 years and have just not used it enough. It was searching for how to fit a DRO on to the cross slide that I came upon MEM and some usefull information. I will reference the member later when I get this first "hello Post" done and hopefully edit and add to it as I get used to it. So will Post before I lose it :(

Cheers Trev

OK so I can edit after Post- that makes it better so can clean up rubish


« Last Edit: June 28, 2023, 05:17:00 PM by perthjack »

Offline crueby

  • Full Member
  • *****
  • Posts: 18677
  • Rochester NY
Re: Hello from Perth, Australia
« Reply #1 on: June 28, 2023, 05:06:03 PM »
Welcome to the forum Trev!   :cheers:

Offline perthjack

  • Jr. member
  • **
  • Posts: 2
Re: Hello from Perth, Australia
« Reply #2 on: June 28, 2023, 05:19:32 PM »
Thanks for that as you may be able to see- I am just getting used to how to post and edit. When sorted Ill put a bit more on intro?

Cheers Trev

Online Kim

  • Global Moderator
  • Full Member
  • *****
  • Posts: 7922
  • Portland, Oregon, USA
Re: Hello from Perth, Australia
« Reply #3 on: June 28, 2023, 05:43:42 PM »
Hi Trev!
Welcome to the forum!

Kim

Offline Dave Otto

  • Full Member
  • *****
  • Posts: 4706
  • Boise, Idaho USA
    • Photo Bucket
Re: Hello from Perth, Australia
« Reply #4 on: June 28, 2023, 06:29:57 PM »
Welcome to MEM!

Dave

Offline RReid

  • Full Member
  • ****
  • Posts: 1699
  • Northern California
Re: Hello from Perth, Australia
« Reply #5 on: June 28, 2023, 08:54:51 PM »
Hello Trev, and welcome!
Regards,
Ron

Offline cnr6400

  • Full Member
  • *****
  • Posts: 2780
Re: Hello from Perth, Australia
« Reply #6 on: June 28, 2023, 09:03:18 PM »
Hi Trev! welcome to the forum.  :cheers:
"I've cut that stock three times, and it's still too short!"

Offline MJM460

  • Full Member
  • ****
  • Posts: 1648
  • Melbourne, Australia
Re: Hello from Perth, Australia
« Reply #7 on: June 29, 2023, 12:16:25 PM »
Hi Trev, another welcome to the forum.

I even have the same model lathe, bought not long before yours.  Looking forward to seeing your progress.

MJM460

The more I learn, the more I find that I still have to learn!

Offline tghs

  • Full Member
  • ****
  • Posts: 1050
Re: Hello from Perth, Australia
« Reply #8 on: June 29, 2023, 01:30:41 PM »
welcome,, I spent a couple of weeks in Perth on a job when I was an international tech,, would gladly go back and spend a few more weeks!!!
what the @#&% over

Offline Roger B

  • Global Moderator
  • Full Member
  • *****
  • Posts: 6164
  • Switzerland
Re: Hello from Perth, Australia
« Reply #9 on: June 29, 2023, 07:12:20 PM »
Welcome to the Forum  :ThumbsUp:  :ThumbsUp:
Best regards

Roger

 

SimplePortal 2.3.5 © 2008-2012, SimplePortal