Author Topic: Now Seal starter motor  (Read 2768 times)

Offline Charles Lamont

  • Full Member
  • ****
  • Posts: 100
Re: Now Seal starter motor
« Reply #75 on: July 20, 2021, 10:48:10 PM »
Yes please. Longer the better!

Offline Allen Smithee

  • Full Member
  • ****
  • Posts: 1073
  • Mordor, Middle Earth
Re: Now Seal starter motor
« Reply #76 on: July 21, 2021, 12:08:22 AM »
OK. It's on my to-do list.

AS
Quidquid latine dictum sit altum sonatur

Offline MJM460

  • Full Member
  • ****
  • Posts: 1400
  • Melbourne, Australia
Re: Now Seal starter motor
« Reply #77 on: July 21, 2021, 04:00:19 AM »
Excellent.  I will be following too.

MJM460

The more I learn, the more I find that I still have to learn!

Offline gadabout

  • Full Member
  • ****
  • Posts: 172
Re: Now Seal starter motor
« Reply #78 on: July 21, 2021, 08:56:42 AM »
Some more pics of the starter fitted to the Seal 15cc
Mark

Offline Vixen

  • Full Member
  • ****
  • Posts: 2145
  • Hampshire UK
Re: Now Seal starter motor
« Reply #79 on: July 21, 2021, 12:59:28 PM »
Hello Mark,

That is a neat and nicely made starter motor installation.  :ThumbsUp: :ThumbsUp:

Mike
It is the journey that matters, not the destination

Offline Roger B

  • Global Moderator
  • Full Member
  • *****
  • Posts: 4918
  • Switzerland
Re: Now Seal starter motor
« Reply #80 on: July 21, 2021, 04:53:17 PM »
That's some neat packaging  :praise2:  :praise2:
Best regards

Roger

Offline Laurentic

  • Full Member
  • ****
  • Posts: 153
  • Nr Yeovil, Somerset, England
Re: Now Seal starter motor
« Reply #81 on: July 21, 2021, 05:57:06 PM »
I like that Mark, looks really good, nice job done there, good on you

Chris

Offline gadabout

  • Full Member
  • ****
  • Posts: 172
Re: Now Seal starter motor
« Reply #82 on: July 22, 2021, 10:42:44 AM »
Thanks for the kind words! Really must JB Weld that casting flaw in the cylinder water jacket, didnít realise how bad it looks!
Regards
Mark

Offline gadabout

  • Full Member
  • ****
  • Posts: 172
Re: Now Seal starter motor
« Reply #83 on: July 22, 2021, 10:46:19 AM »
When I get time I will take a pic or two of the starter parts in an exploded view if anyone is interested
Mark

Offline Charles Lamont

  • Full Member
  • ****
  • Posts: 100
Re: Now Seal starter motor
« Reply #84 on: July 22, 2021, 11:59:01 AM »
This is the starter gearbox I am intending for the Seagull. It will drive on the timing end of the crankshaft. The pink output gear is fixed to the black cup that carries the red outer race of the sprag clutch. The inner race is keyed to the output shaft, and these are the only bits that revolve when the engine is running
« Last Edit: July 22, 2021, 12:05:25 PM by Charles Lamont »

Offline gadabout

  • Full Member
  • ****
  • Posts: 172
Re: Now Seal starter motor
« Reply #85 on: July 23, 2021, 12:59:15 AM »
Charles,
That looks nice! I was wondering how you had it set up, might have to revisit mine to see if I can fit a one way bearing to the flywheel.
Regards
Mark