Recent Posts

Pages: [1] 2 3 ... 10
1
Your Own Design / Re: Kearsarge Windlass Engines
« Last post by ddmckee54 on Today at 05:49:58 PM »
Just out of idle curiosity, did you Count the Number of Cranks it took to bring the top down to finished height?  That was some mighty fine CNCing.
2
Your Own Design / Re: Kearsarge Windlass Engines
« Last post by crueby on Today at 04:20:33 PM »
Bunch more done on the engine bed. The insides of the openings have been taken out to final size and smoothed with a long end mill

Then went around the outside and took the top down partway, to where the angled gussets will stick out. The screws were taken out one at a time as this work went, each replaced with a shorter one when that section was done. On the near side the cut was straight across the length, on the side away from the camera it went out and back around the extensions to the openings (which are to give the cranks more room) as well as a block in the center which will become a support for an angled brace up to the engine blocks.


Then started taking the top surface down to the final height, here its halfway done:

and all the way across

Then laid out and cut the side away from the camera down farther, that side has a lower height except where the post supports are on the two ends

Next steps are to take the sides down to leave just the low flanges, leaving the gussets at the ends and one in the middle. Here is after first set of passes on one side, taking it down as far as this end mill will reach. Will come back and take it down the rest of the way with a longer one. Again, the screws are being taken out one at a time while working across that portion, and they are being replaced with shorter ones as it goes.


3
Chatterbox / Re: Is Facebook as bad as I have read, or is it OK?
« Last post by Jasonb on Today at 04:04:01 PM »
Although I have not use FB Market place I have got commissions via facebook both to build engines and also do the CAD works for reverse engineering. All went OK including payments done over the net.

These days you have got as much chance of being scammed on there as anywhere else be it a cold call or scam email.

All Cookies fresh and ready to take me quickly to anything I visit again rather than deleting and/or rebooting 10 times a day.
4
Chatterbox / Re: Is Facebook as bad as I have read, or is it OK?
« Last post by Jo on Today at 03:44:04 PM »
In addition:

After every visit to Farcebook make sure you delete all the cookies they have loaded onto your machine and I normally reboot my machine and delete the cookies again.

If you post pictures (any where on the internet) be wary of what is in the background and question if you even want to post the picture at all. For example my friend's 2 year old granddaughter sadly died by drowning in the local pond. The local press acquired a photo on the family and published it. This caused of bad feeling in the village as everyone was being accused of providing this photo to the press until it was realised it was openly available on the social media site and that is where the press acquired it  >:(

Be careful of buyers on Farcebook there are a lot of scammers on there, cash on collection is about the only way I would trade on there - which I never would  :hellno: . (A test of good internet hygiene is to ask yourself have you have ever been scammed.)

Jo
5
From Kits/Castings / Re: Building a Redwing
« Last post by Jasonb on Today at 03:10:35 PM »
5BA would probably be the simple one to go for as most ME's in the UK have that, a few thou smaller but at 43tpi quite fine. Could even go down to M3 which works out at 51tpi as I doubt you have M3.5

Attached my conversion chart for when I'm working on American kits.
6
From Kits/Castings / Re: Building a Redwing
« Last post by Twizseven on Today at 02:45:44 PM »
Currently making the Lunkenheimer fuel mixer. The plans call for 6-48 thread for the fuel needle valve. I do not have this tap/die and would prefer not to buy for a one off. What thread would you suggest that is fine enough to give fine movement.
Many thanks
Colin
7
Chatterbox / Re: Is Facebook as bad as I have read, or is it OK?
« Last post by Woodguy on Today at 02:09:21 PM »
Facebook can be very invasive. I suggest that if you want to use it, you should create a new email address and use that when signing up. This will avoid most of the problems as Facebook will not be able to dig through your contacts and find people you may have interacted with.  Be careful when responding to the questions the signup process will ask.  Don't provide any of the optional information that can be displayed by Facebook, such as work history, education, life events etc.


Once you are done with whatever you wanted Facebook for - delete your account.


Am I paranoid?  It's based on experience some years ago and things have improved - they say.


As with any other platform where goods are bought/sold, exercise due caution when dealing with buyers/sellers.
8
Chatterbox / Is Facebook as bad as I have read, or is it OK?
« Last post by A7er on Today at 01:49:11 PM »
Is Facebook to be avoided at all costs? I have a lot of musical instruments to sell, as well as music scores. Facebook seems to be the ideal marketplace. What say you?

Lee
9
Nice progress Willy  :ThumbsUp:

Per
10
Additive Machining / Re: Moon Clock
« Last post by wagnmkr on Today at 09:14:02 AM »
Thanks Krypto.
Pages: [1] 2 3 ... 10
SimplePortal 2.3.5 © 2008-2012, SimplePortal