Author Topic: LANZ tractor  (Read 17151 times)

Offline Tapsa

  • Full Member
  • ****
  • Posts: 62
Re: LANZ tractor
« Reply #30 on: July 07, 2019, 03:30:00 PM »
Hi all, I've been busy with my work, here some photos how my project proceeds.
Smoke pipe project and all parts fotos.
Tapsa




















Offline Admiral_dk

  • Full Member
  • *****
  • Posts: 3752
  • Søften - Denmark
Re: LANZ tractor
« Reply #31 on: July 07, 2019, 09:52:14 PM »
You are making good progress, but I must ask about the crank in the bottom of the page - is it made from several pieces not put completely together yet or did you have an accident with it ?

Offline Tapsa

  • Full Member
  • ****
  • Posts: 62
Re: LANZ tractor
« Reply #32 on: July 08, 2019, 04:50:27 PM »
Hello  Admiral_dk
the parts are as in the drawings
Tapsa




Offline b.lindsey

  • Global Moderator
  • Full Member
  • *****
  • Posts: 13860
  • Dallas, NC, USA
    • Workbench-Miniatures
Re: LANZ tractor
« Reply #33 on: July 08, 2019, 08:16:19 PM »
Nice looking collection of parts so far. I think Admiral was asking if the crank is fully assembled yet because of the angle of the crank cheeks in the picture.

Bill
« Last Edit: July 08, 2019, 09:44:46 PM by b.lindsey »

Offline Admiral_dk

  • Full Member
  • *****
  • Posts: 3752
  • Søften - Denmark
Re: LANZ tractor
« Reply #34 on: July 08, 2019, 09:30:00 PM »
Quote
I think Admiral was asking if the crack is fully assembled yet because of the angle of the crank cheeks in the picture.

Bill got that one right  :ThumbsUp:

Best wishes

Per

Offline Tapsa

  • Full Member
  • ****
  • Posts: 62
Re: LANZ tractor
« Reply #35 on: July 09, 2019, 05:57:17 AM »
You are right, the crank is not fully assembled yet. Any of the parts have not been finalized yet.

Tapsa

Offline Tapsa

  • Full Member
  • ****
  • Posts: 62
Re: LANZ tractor
« Reply #36 on: July 14, 2019, 05:07:03 PM »
Hello everyone.
at work it's been so busy that had very little time for workshop.
Some little parts I have done.
Tapsa








Offline Tapsa

  • Full Member
  • ****
  • Posts: 62
Re: LANZ tractor
« Reply #37 on: July 23, 2019, 06:36:50 PM »
Hey everybody. It's been a busy time and I haven't got time to do parts at the workshop. All time I had went to cleaning. Today I had couple of hours to do parts.






Big big cleaning two days






More smoke pipe parts


Offline sid pileski

  • Full Member
  • ****
  • Posts: 162
Re: LANZ tractor
« Reply #38 on: July 23, 2019, 09:21:15 PM »
Watching this build! Looking good.
I'm going to re-model(3D) it in inch units.
Just a thought. I have my vacuum going as I'm milling parts.
Makes for a faster clean up!

Sid

Offline Tapsa

  • Full Member
  • ****
  • Posts: 62
Re: LANZ tractor
« Reply #39 on: July 24, 2019, 04:29:29 PM »
Hello everybody
I'm sorry that I can't answer to everyone. I have to ask help in writing in English. You all work so well.
Today I made the smoke pipe, not finished yet (not polished).

 




Offline Ye-Ole Steam Dude

  • Full Member
  • ****
  • Posts: 1571
  • Deep East Texas on Sam Rayburn Lake
Re: LANZ tractor
« Reply #40 on: July 24, 2019, 04:34:09 PM »
Hello Tapsa,

That stack is going to look really nice after a polish job. I am curious, are you doing the taper using the drill motor?

Have a great day,
Thomas
Thomas

Offline Tapsa

  • Full Member
  • ****
  • Posts: 62
Re: LANZ tractor
« Reply #41 on: July 24, 2019, 05:29:35 PM »
Hello Thomas,

if I understood your question right, I'm not doing that.


Offline mike mott

  • Full Member
  • ****
  • Posts: 418
  • Alberta Canada
Re: LANZ tractor
« Reply #42 on: July 26, 2019, 04:40:55 AM »
So what were you using the drill for? :headscratch:

Mike
If you can imagine it you can build it

Offline Tapsa

  • Full Member
  • ****
  • Posts: 62
Re: LANZ tractor
« Reply #43 on: July 26, 2019, 05:47:54 AM »
Hi, I used the drill to make it easier to turn the cone.
Tapsa

Offline Tapsa

  • Full Member
  • ****
  • Posts: 62
Re: LANZ tractor
« Reply #44 on: July 27, 2019, 05:18:45 PM »
Hello all.

Today I made a few small parts. There is a problem with the motor body, because I have not yet received the material I have ordered.
Tapsa































 

SimplePortal 2.3.5 © 2008-2012, SimplePortal