Author Topic: AOG’s version of Elmer’s number 5 geared engine  (Read 2294 times)

Offline bent

  • Full Member
  • ****
  • Posts: 422
  • Wet side of Washington State, USA
Re: AOG’s version of Elmer’s number 5 geared engine
« Reply #30 on: June 04, 2019, 05:59:33 PM »
Looks good so far, Tony.  Rest and heal up, the projects can wait.

Offline AOG

  • Full Member
  • ****
  • Posts: 672
Re: AOG’s version of Elmer’s number 5 geared engine
« Reply #31 on: October 12, 2019, 08:47:09 PM »
It’s been quite a while since I posted in this thread. Between work and my still not completely healed back my time in the shop has been limited to an occasional 10 min here and 20 min there. I was looking at the pictures in my camera and I realized I had enough for a post or two so let’s get caught up. On my last post I had finished the piston and piston rod. Next up was the valve chest. A blank was cut and squared off. Then it was centered up in the four jaw and the hole for the gland drilled and tapped.



The end was then turned round.



To keep things concentric the part was flipped and the rounded end was placed in a collet chuck. The other end was turned round and domed over.



Then over to the mill where the corners of the cavity where drilled out.



The center was then milled out.



The mounting holes were put in by coordinate drilling using the DRO.



The valve chest was flipped on it’s side and the intake hole drilled and tapped.



At that point I realized that I hadn’t drilled out the end dome to support the valve rod so it was back into the lathe to complete that operation.



Here is the completed valve chest prior filing and clean up.



That’s it for now. I have enough pics for another post that I’ll put up once I get them organized.

Tony


Sent from my iPad using Tapatalk

Offline b.lindsey

  • Global Moderator
  • Full Member
  • *****
  • Posts: 13687
  • Dallas, NC, USA
    • Workbench-Miniatures
Re: AOG’s version of Elmer’s number 5 geared engine
« Reply #32 on: October 13, 2019, 01:38:00 PM »
Good to see some progress Tony. Hope the back continues to improve as well.

Bill

Offline AOG

  • Full Member
  • ****
  • Posts: 672
Re: AOG’s version of Elmer’s number 5 geared engine
« Reply #33 on: October 13, 2019, 07:56:57 PM »
Thanks  Bill, here is the second part of my “let’s get caught up “ post. The next components made were the valve plate and valve chest cover. The blanks were squared up and clamped together. Then the mounting holes were coordinate drilled using the DRO.



Then the valve plate holes were drilled.



 Next up was the valve itself. The end of a piece of brass bar was squared up and the pocket was milled.



The part was flipped over and milled to size.



Then the slots for the valve nut and rod were milled.



The valve was completed by cutting it off of the parent stock and milling it to length. The next part was the valve rod. My lathe doesn’t have a good means of supporting the end of such a small part so the profile was turned and threaded in short sections to minimize bending.







Then it was over to the mill to put in the flats and drill the hole.



The valve rod was parted off and faced to length. The last piece in this update is the eccentric. The parent stock was chucked in the four jaw and faced off. Then the shaft hole was drilled and reamed.



The four jaw was offset and the eccentric turned.



Then over to the mill to drill and tap for the grub screw.



The eccentric was parted off and faced to length. I will conclude this update with a family shot of where we are with this project.



Till next time

Tony


Sent from my iPad using Tapatalk

Offline b.lindsey

  • Global Moderator
  • Full Member
  • *****
  • Posts: 13687
  • Dallas, NC, USA
    • Workbench-Miniatures
Re: AOG’s version of Elmer’s number 5 geared engine
« Reply #34 on: October 14, 2019, 12:23:00 AM »
Nice family shot Tony. Thanks again for the updates.

Bill

Offline bent

  • Full Member
  • ****
  • Posts: 422
  • Wet side of Washington State, USA
Re: AOG’s version of Elmer’s number 5 geared engine
« Reply #35 on: October 14, 2019, 04:49:29 PM »
Nice work Tony!