Author Topic: Lehmann Stirling Engine  (Read 2794 times)

Offline toolznthings

  • Full Member
  • ****
  • Posts: 497
  • Kent,Ohio
Re: Lehmann Stirling Engine
« Reply #30 on: March 08, 2019, 02:06:41 AM »
Lots of great progress !! Moving along nicely.  :ThumbsUp:
Thanks for the visit !
Brian

Offline scc

  • Full Member
  • ****
  • Posts: 540
  • Lancashire, UK
Re: Lehmann Stirling Engine
« Reply #31 on: March 08, 2019, 04:23:52 PM »
Excellent :popcorn:

Offline yogi

  • Full Member
  • ****
  • Posts: 403
  • Duncannon, PA USA
    • Yogi's Workshop
Re: Lehmann Stirling Engine
« Reply #32 on: April 05, 2019, 08:29:08 PM »
Thanks everyone for the kind comments! It's very much appreciated.  :cheers:

Progress is slow, but I do have a part to share with you guys.

The base plate is milled from 3/8" 6061 plate. I divided the milling operation into two, milling two sides at the time.
Carefully placing the plate on 123 blocks, making sure the blocks don't interfere with the tool path. Clamped down, again carefully checking the clamps are not interfering, the right and the left side are milled.




Finish pass:




I moved the claps one at the time to the side of the plate, making sure not to move the part from its position, to mill the remaining two sides. Again, making sure the clamps are clear from the tool path.






In the same set up, I spot drilled the location for the mounting holes. Here the base plate after it came off the mill:




The drilling and tapping was done manually on the Bridgeport.
The finished part:




And the mandatory family shot of the parts so far:




Thanks everyone for following along, and stay tuned for more.
Yogi


Offline yogi

  • Full Member
  • ****
  • Posts: 403
  • Duncannon, PA USA
    • Yogi's Workshop
Re: Lehmann Stirling Engine
« Reply #33 on: April 20, 2019, 01:12:27 AM »

For the split bearings, I first milled the bronze stock into halves.






Chucking the two pieces in the 4 jaw, the bearings are turned and parted off.








Last operation is to drill holes in the bearing half's. In the bottom half the hole is for a pin to prevent the bearing from rotating, in the top it's for the oil passage.




The finished bearings:




And the bearing installed in the bearing blocks.





Thanks everyone for following along, and stay tuned for more.
Yogi






Offline yogi

  • Full Member
  • ****
  • Posts: 403
  • Duncannon, PA USA
    • Yogi's Workshop
Re: Lehmann Stirling Engine
« Reply #34 on: May 10, 2019, 10:13:07 PM »
The next parts for the engine I made are the crank and return crank. They are made from 303 stainless.

The first side is finished to full depth.






The second side is then finished using the trusty soft jaws.






The finished cranks:









Thanks everyone for following along, and stay tuned for more.
Yogi

Offline Plani

  • Full Member
  • ****
  • Posts: 65
Re: Lehmann Stirling Engine
« Reply #35 on: May 11, 2019, 08:43:53 PM »
Great progress and very nice parts  :ThumbsUp: :ThumbsUp: :ThumbsUp:
Looking good!


Plani

Offline Art K

  • Full Member
  • ****
  • Posts: 1069
  • Madison, Wisconsin USA
Re: Lehmann Stirling Engine
« Reply #36 on: May 12, 2019, 02:27:17 AM »
Yogi,
Missed this build I will be following along. I have to admit that it is no fun boring a piece that long on the cylinder 8 inches. that's where you find how good your equipment is. Looks great so far.
Art
"The beautiful thing about learning is that no one can take it away from you" B.B. King

Online b.lindsey

  • Global Moderator
  • Full Member
  • *****
  • Posts: 13251
  • Dallas, NC, USA
    • Workbench-Miniatures
Re: Lehmann Stirling Engine
« Reply #37 on: May 12, 2019, 02:35:57 PM »
Wonderful family shot yogi. This really is quite a large engine but the motion is fascinating!!  Still following along.

Bill

Offline toolznthings

  • Full Member
  • ****
  • Posts: 497
  • Kent,Ohio
Re: Lehmann Stirling Engine
« Reply #38 on: May 13, 2019, 01:13:55 AM »
As always, nice looking parts !   Following along  :popcorn:  :ThumbsUp:
Thanks for the visit !
Brian

Offline PJPickard

  • Full Member
  • ****
  • Posts: 131
Re: Lehmann Stirling Engine
« Reply #39 on: May 13, 2019, 11:06:55 AM »
Great work on a fav of mine! I love your Maho!

Offline Dave Otto

  • Full Member
  • *****
  • Posts: 3549
  • Boise, Idaho USA
    • Photo Bucket
Re: Lehmann Stirling Engine
« Reply #40 on: May 13, 2019, 11:45:56 PM »
Very nice Yogi!

Dave