Author Topic: 15cm3 Hackworth-Marshall  (Read 3116 times)

Offline Malevthi

  • Full Member
  • ****
  • Posts: 14
    • BloOOo Forum
15cm3 Hackworth-Marshall
« on: March 29, 2016, 10:25:59 PM »
Hello,
I drew this twin engine. ( 0.91in3 )
"Verdon"
It was built by Max Rousseau:
<a href="https://www.youtube.com/watch?v=MFykZLXvp3Y" target="_blank">http://www.youtube.com/watch?v=MFykZLXvp3Y</a>
« Last Edit: March 31, 2016, 06:50:31 AM by Malevthi »

Offline yogi

  • Full Member
  • ****
  • Posts: 450
  • Duncannon, PA USA
    • Yogi's Workshop
Re: 15cm3 Hackworth-Marshall
« Reply #1 on: March 31, 2016, 01:06:31 AM »
Very interesting!  :ThumbsUp:
What's the valve gear you are using on this engine? Maybe you could post some close up pictures.
Thanks for sharing. 

Offline Jo

  • Administrator
  • Full Member
  • *****
  • Posts: 15293
  • Hampshire, england.
Re: 15cm3 Hackworth-Marshall
« Reply #2 on: March 31, 2016, 08:20:44 AM »
Nice little engine  8)

Thierry, are the drawings available for it ?

Jo
Enjoyment is more important than achievement.

Offline Malevthi

  • Full Member
  • ****
  • Posts: 14
    • BloOOo Forum
Re: 15cm3 Hackworth-Marshall
« Reply #3 on: March 31, 2016, 10:56:16 AM »


The drawings are available. I soon put them.
« Last Edit: March 31, 2016, 11:04:44 AM by Malevthi »

Offline Malevthi

  • Full Member
  • ****
  • Posts: 14
    • BloOOo Forum
Re: 15cm3 Hackworth-Marshall
« Reply #4 on: March 31, 2016, 01:54:38 PM »
Here drawings

Offline Malevthi

  • Full Member
  • ****
  • Posts: 14
    • BloOOo Forum
Re: 15cm3 Hackworth-Marshall
« Reply #5 on: March 31, 2016, 01:57:51 PM »
The following

Offline Jo

  • Administrator
  • Full Member
  • *****
  • Posts: 15293
  • Hampshire, england.
Re: 15cm3 Hackworth-Marshall
« Reply #6 on: March 31, 2016, 01:58:09 PM »
Thanks Thierry.

I think a few of out members might find your engine very tempting to make  8)

Jo
Enjoyment is more important than achievement.

Offline tvoght

  • Full Member
  • ****
  • Posts: 1001
  • Indiana
Re: 15cm3 Hackworth-Marshall
« Reply #7 on: March 31, 2016, 03:03:35 PM »
Those are very nicely done drawings for an attractive engine, Thierry. Thanks for posting them.

--Tim

Offline Malevthi

  • Full Member
  • ****
  • Posts: 14
    • BloOOo Forum
Re: 15cm3 Hackworth-Marshall
« Reply #8 on: March 31, 2016, 03:57:51 PM »
Thank you for the compliments

I added 2 ball bearings

 

SimplePortal 2.3.5 © 2008-2012, SimplePortal