Author Topic: 2016 N.A.M.E.S. Expo, info flyer  (Read 14814 times)

Offline PTsideshow

  • Full Member
  • ****
  • Posts: 54
2016 N.A.M.E.S. Expo, info flyer
« on: January 17, 2016, 12:37:41 PM »
With gas heading back to the good ole days, It's time to make plans for the 2016 N.A.M.E.S. Expo, whether as an exhibitor or vendor.

Offline PTsideshow

  • Full Member
  • ****
  • Posts: 54
Re: 2016 N.A.M.E.S. Expo, info flyer
« Reply #1 on: February 02, 2016, 10:28:33 AM »
Time to get your motel reservations

Offline PTsideshow

  • Full Member
  • ****
  • Posts: 54
Re: 2016 N.A.M.E.S. Expo, info flyer
« Reply #2 on: March 02, 2016, 10:51:07 AM »
Everything moving along toward the show dates and vendors booths filling up.

Offline PTsideshow

  • Full Member
  • ****
  • Posts: 54
Re: 2016 N.A.M.E.S. Expo, info flyer
« Reply #3 on: March 14, 2016, 09:26:52 AM »
It's getting down to crunch time, For the vendors as of Saturday only one space was left.

Offline sshire

  • Full Member
  • *****
  • Posts: 3044
    • LS Editions
Re: 2016 N.A.M.E.S. Expo, info flyer
« Reply #4 on: March 14, 2016, 11:31:00 AM »
Can't wait. Reservations made. Engines polished.
Best,
Stan

Offline PTsideshow

  • Full Member
  • ****
  • Posts: 54
Re: 2016 N.A.M.E.S. Expo, info flyer
« Reply #5 on: March 14, 2016, 11:52:14 AM »
Have a safe trip! Looking forward to see you again.

Offline sshire

  • Full Member
  • *****
  • Posts: 3044
    • LS Editions
Re: 2016 N.A.M.E.S. Expo, info flyer
« Reply #6 on: March 14, 2016, 04:38:31 PM »
Who else is going?
A MEM table like last year would be nice.
Best,
Stan

Offline tvoght

  • Full Member
  • ****
  • Posts: 921
  • Indiana
Re: 2016 N.A.M.E.S. Expo, info flyer
« Reply #7 on: March 14, 2016, 05:16:47 PM »
Stan,
I'll be there, and it would be nice to sit with others from the group. This is as good a place as any to ask: what fitting do I need to hook up to an air valve at the table? I believe it's 1/4 NPT, but what gender? I still hope to have my Roberts Mechanism steam engine running by then, and I have acquired the trick regulator setup that you (Stan) use, the SMC ARM1000.

--Tim
« Last Edit: March 15, 2016, 12:56:14 AM by tvoght »

Offline gldavison

  • Full Member
  • ****
  • Posts: 142
  • Tarkio, Mo.
Re: 2016 N.A.M.E.S. Expo, info flyer
« Reply #8 on: March 14, 2016, 05:50:53 PM »
I plan too be there also.

Stan you started something there, I also acquired one of those regulators.

Get the banner up.
« Last Edit: March 14, 2016, 05:56:56 PM by gldavison »

Offline PTsideshow

  • Full Member
  • ****
  • Posts: 54
Re: 2016 N.A.M.E.S. Expo, info flyer
« Reply #9 on: March 14, 2016, 11:23:21 PM »
The fitting on the manifold are 1/4" petcocks with the female end facing user end. Stan plant the Banner and stake out some space it would be helpful for him to know how many will be there under the MEM banner.

Offline jeff l

  • Full Member
  • ****
  • Posts: 205
Re: 2016 N.A.M.E.S. Expo, info flyer
« Reply #10 on: March 15, 2016, 01:53:16 AM »
I plan to go .

Offline Art K

  • Full Member
  • ****
  • Posts: 1129
  • Madison, Wisconsin USA
Re: 2016 N.A.M.E.S. Expo, info flyer
« Reply #11 on: March 15, 2016, 03:09:56 AM »
Stan,
I plan to be there. Looking forward to seeing everyone again.
Art
"The beautiful thing about learning is that no one can take it away from you" B.B. King

Offline tvoght

  • Full Member
  • ****
  • Posts: 921
  • Indiana
Re: 2016 N.A.M.E.S. Expo, info flyer
« Reply #12 on: March 15, 2016, 12:38:12 PM »
The fitting on the manifold are 1/4" petcocks with the female end facing user end. Stan plant the Banner and stake out some space it would be helpful for him to know how many will be there under the MEM banner.

Thanks!

--Tim

Offline RonGinger

  • Full Member
  • ****
  • Posts: 238
  • Boothbay Maine USA
    • Pleasant Cove Models
Re: 2016 N.A.M.E.S. Expo, info flyer
« Reply #13 on: March 15, 2016, 01:14:57 PM »
I am planning to be there, only missed #1 because I did not know about it but have made it every other year. It is just about a 2000 mile round trip for me, and for 26 years that is about 56,000 miles I have driven to be there. How is that for a crazy thought?

I will be doing my nearly annual talk "Adventures in home shop CNC" on Saturday at 10:30. Hope to see a bunch of you there. I will be reporting on the new CNC lathe conversion I am doing for theCNCworkshop.com. We plan to have the proto model there running.

Online kvom

  • Full Member
  • ****
  • Posts: 1983
Re: 2016 N.A.M.E.S. Expo, info flyer
« Reply #14 on: March 15, 2016, 02:00:47 PM »
I plan to be there as well, although unsure if I'm going to drive or fly.  I'm definitely interested in the CNC lathe conversion project.