Author Topic: Dale's k 27 By Kozo  (Read 63489 times)

Offline b.lindsey

  • Global Moderator
  • Full Member
  • *****
  • Posts: 13860
  • Dallas, NC, USA
    • Workbench-Miniatures
Re: Dale's k 27 By Kozo
« Reply #150 on: November 24, 2017, 01:48:12 PM »
Glad to see you back in the shop Dale. Nice looking Tormach too  :)

Bill

Online steamer

  • Global Moderator
  • Full Member
  • *****
  • Posts: 12697
  • Central Massachusetts, USA
Re: Dale's k 27 By Kozo
« Reply #151 on: November 24, 2017, 02:01:10 PM »
You're going to love the 1100

The engine is coming along beautifully!     That's fantastic work!!!!

Dave

"Mister M'Andrew, don't you think steam spoils romance at sea?"
Damned ijjit!

Offline kvom

  • Full Member
  • *****
  • Posts: 2649
Re: Dale's k 27 By Kozo
« Reply #152 on: November 24, 2017, 03:39:01 PM »
I recently converted my mill to run under PathPilot, and I like it more than Mach3.  However it requires TTS tool holders to run as intended.  Since I didn't care to spend the $ to acquire these, I need to stop the program at every tool change so that I can zero Z.  At that point I restart the program manually at the tool change line.  Other than that, I'm happy with the changeover, and can get faster rapids (now running 120ipm vs 75 previously).

Offline Mcgyver

  • Full Member
  • ****
  • Posts: 394
  • Toronto
Re: Dale's k 27 By Kozo
« Reply #153 on: November 24, 2017, 03:57:06 PM »
that is a serious looking engine, very nice!

Offline dalem9

  • Full Member
  • ****
  • Posts: 132
Re: Dale's k 27 By Kozo
« Reply #154 on: November 24, 2017, 08:31:50 PM »
THANKS GUYS  KVON JUST BUY A FEW HOLDERS AT A TIME THEY REALLY ARE NICE TO HAVE AND USE .tHEY WOULD NOT BE THAT HARD TO ADAP  OR EVEN MAKE YOUR OWN . THEY SURE ARE NICE.

Offline dalem9

  • Full Member
  • ****
  • Posts: 132
Re: Dale's k 27 By Kozo
« Reply #155 on: December 19, 2017, 10:52:33 PM »


Here is my pilot . Should I paint the whole thing or leave as it is . 

  .

Online Kim

  • Global Moderator
  • Full Member
  • *****
  • Posts: 7862
  • Portland, Oregon, USA
Re: Dale's k 27 By Kozo
« Reply #156 on: December 20, 2017, 05:28:37 AM »
No, input on the paint question, but, wow! that looks great!
Kim

Offline dalem9

  • Full Member
  • ****
  • Posts: 132
Re: Dale's k 27 By Kozo
« Reply #157 on: December 23, 2017, 07:46:39 PM »
Here is the pilot after painting .

Online Kim

  • Global Moderator
  • Full Member
  • *****
  • Posts: 7862
  • Portland, Oregon, USA
Re: Dale's k 27 By Kozo
« Reply #158 on: December 24, 2017, 05:06:36 AM »
And it looks even better with paint!
Kim

Offline dalem9

  • Full Member
  • ****
  • Posts: 132
Re: Dale's k 27 By Kozo
« Reply #159 on: December 26, 2017, 11:43:43 PM »
Here is the front pilot and steps and opening bar . I am going to sand blast and paint .Just took these so you can see it better . Hope you all had a Very Merry Christmas !

Offline b.lindsey

  • Global Moderator
  • Full Member
  • *****
  • Posts: 13860
  • Dallas, NC, USA
    • Workbench-Miniatures
Re: Dale's k 27 By Kozo
« Reply #160 on: December 27, 2017, 12:41:39 AM »
Beautiful Dale.  :ThumbsUp:

Bill

Offline dalem9

  • Full Member
  • ****
  • Posts: 132
Re: Dale's k 27 By Kozo
« Reply #161 on: December 27, 2017, 02:31:48 AM »
Thanks

Offline dalem9

  • Full Member
  • ****
  • Posts: 132
Re: Dale's k 27 By Kozo
« Reply #162 on: February 23, 2018, 09:03:59 PM »
Here are the frames and doors I made for the headlight on my K27. There will be a light in it so you can see the number board numbers . Hope you guys like them they were a lot of work making .

Offline zeeprogrammer

  • Full Member
  • *****
  • Posts: 6811
  • West Chester, PA, USA
Re: Dale's k 27 By Kozo
« Reply #163 on: February 23, 2018, 11:50:58 PM »
Wow. Nice pics!  :ThumbsUp: I can see a lot of work was put into that.
Carl (aka Zee) Will sometimes respond to 'hey' but never 'hey you'.
"To work. To work."
Zee-Another Thread Trasher.

Offline dalem9

  • Full Member
  • ****
  • Posts: 132
Re: Dale's k 27 By Kozo
« Reply #164 on: February 24, 2018, 12:14:21 AM »
Thanks Zee !

 

SimplePortal 2.3.5 © 2008-2012, SimplePortal